The Best Brick Sealer for Exterior Walls, Chimneys and Pavers

Updated: November 2026 | By Sophie Ulman

Seal brick with the wrong formula and you do not get protection — you get a glossy film trapping water behind it, and that trapped moisture freezes every winter until the brick face pops off in chunks. A good brick sealer keeps rain, salt and freeze-thaw cycles out of the masonry while still letting the wall breathe; a bad one locks moisture in and speeds up exactly the damage you were trying to prevent. Below are four sealers that actually match the job — walls, chimneys or pavers — and the one spec that matters more than brand name: whether the formula is vapor-permeable or not.

I have resealed enough brick chimneys and garden walls to know the mistake almost never shows up on day one. It shows up two winters later, as spalling brick faces where a film-forming sealer trapped water that used to evaporate out on its own. Here is which sealers breathe, which ones do not, and how to tell before you buy.

Quick Picks

ProductBest ForGet It
DRYLOK Siloxane 7 Brick & Masonry Penetrating Sealer
1 Gallon, Clear
Overall pick for exterior brick wallsCheck Price on Amazon ->
Rain Guard Water Sealers Brick Sealer
Natural Finish, 1 Gallon
New or newly-cleaned brick that still needs to breatheCheck Price on Amazon ->
MasonryDefender Chimney Brick Sealer
Clear Water-Based Siloxane, 1 Gal
Chimneys and other vertical masonry exposed to constant weatherCheck Price on Amazon ->
Seal-Krete Clear-Seal Satin Concrete Protective Sealer
1 Gallon
Brick pavers and walkways that take foot trafficCheck Price on Amazon ->

Best Brick Sealers, Reviewed

SEALBEST OVERALL FOR EXTERIOR BRICK WALLS

DRYLOK Siloxane 7 Brick & Masonry Penetrating Sealer (1 Gallon, Clear)

This is a penetrating sealer, not a topical coating: it soaks into the brick and mortar and reacts with the minerals inside to form a water-repellent barrier below the surface, rather than sitting on top as a film. Because the repellent layer is inside the brick instead of on it, water vapor already inside the wall can still escape outward — the defining difference between a sealer that protects brick and one that eventually damages it.

It is suited to standard exterior brick walls, foundations and retaining walls where you want invisible, matte protection that does not change the brick’s natural color or texture. The honest limitation: because it soaks in rather than sitting on top, it will not add any sheen or “wet look,” and manufacturer guidance calls for reapplication roughly every five to seven years on a wall exposed to full weather.

Manufacturer spec: siloxane-based penetrating sealer rated for brick, concrete and masonry, water-based formula, clear matte finish with no color change.

Pros

  • Penetrates rather than filming over, so the wall keeps breathing
  • No color change or added sheen — brick looks untouched
  • Rated for brick, concrete and general masonry in one product

Cons

  • No gloss or “wet look” option if that is what you want
  • Needs reapplication roughly every five to seven years

Best for

  • Standard exterior brick walls and foundations where invisible, breathable protection matters more than appearance

Check Price on Amazon ->

Via Amazon.com
SEALBEST FOR NEW OR NEWLY-CLEANED BRICK

Rain Guard Water Sealers Brick Sealer (Natural Finish, 1 Gallon)

A silane/siloxane penetrating sealer built specifically for brick and mortar rather than concrete first, which matters because mortar and brick absorb water at different rates and a formula tuned for brick handles that mismatch better than a generic masonry sealer. It is ready-to-use, requiring no mixing or dilution before it goes on.

It is suited to brick that is new, recently repointed, or recently pressure-washed — surfaces where you want a sealer dialed in for brick specifically rather than a one-size-fits-all concrete formula. The honest limitation: because it is a dedicated ready-to-use liquid rather than a concentrate, coverage per gallon runs lower than concentrate formulas that you dilute yourself, so a large wall needs more gallons.

Manufacturer spec: silane/siloxane waterproofer formulated for brick and mortar surfaces, natural finish, ready-to-use with no dilution required.

Pros

  • Formulated specifically for brick and mortar, not concrete first
  • Ready-to-use — no mixing before application
  • Natural finish leaves no visible sheen

Cons

  • Lower coverage per gallon than a dilute-it-yourself concentrate
  • Not the choice if you are also sealing a large concrete driveway in the same pass

Best for

  • New brick, freshly repointed mortar joints, or brick that was just pressure-washed and needs protection dialed in for brick specifically

Check Price on Amazon ->

Via Amazon.com
SEALBEST FOR BRICK CHIMNEYS

MasonryDefender Chimney Brick Sealer (Clear Water-Based Siloxane, 1 Gal)

A water-based siloxane sealer marketed specifically for chimneys and other vertical masonry that takes the most direct weather exposure on a house — the highest point, with no roof overhang to shed rain away from it. Like the other penetrating formulas here, it is designed to stay breathable rather than seal the surface shut.

It is suited to chimney stacks, crowns and any tall, exposed brick section where freeze-thaw cycling does the most damage, since trapped moisture at the top of a house has nowhere to drain and nothing shielding it from direct rain. The honest limitation: a chimney is a job that usually means working at height, so factor in ladder or roof-access safety before you buy any sealer for this specific use.

Manufacturer spec: water-based siloxane sealer marketed for chimney brick and other vertical exterior masonry, clear finish, breathable formula.

Pros

  • Marketed specifically for chimneys, the most exposed brick on most homes
  • Water-based siloxane stays breathable like the other penetrating picks
  • Clear finish does not change the chimney’s appearance

Cons

  • Chimney application is a height-access job, not a ground-level one
  • Not the pick if you are only sealing a low garden wall

Best for

  • Chimney stacks and other tall, fully-exposed vertical brick sections

Check Price on Amazon ->

Via Amazon.com
Seal-Krete Clear-Seal Satin Concrete Protective Sealer product image

SEALBEST FOR BRICK PAVERS AND WALKWAYS

Seal-Krete Clear-Seal Satin Concrete Protective Sealer (1 Gallon)

Unlike the three penetrating sealers above, this is a topical, film-forming acrylic sealer built for horizontal, walked-on surfaces — brick pavers, walkways and patios — where a thin protective film on top of the surface resists stains, salt and tire pickup in a way a purely penetrating formula on a foot-traffic surface cannot.

It is suited to brick or concrete pavers, walkways and pool-deck surfaces that need resistance to oil, salt and staining as much as water — our guide to painting concrete pavers covers the alternative approach if you want color instead of a clear sealer. The honest limitation: because it forms a thin film rather than soaking in, it is built for horizontal paver and walkway surfaces, not for vertical brick walls or chimneys — using a film-forming sealer on a vertical wall is the mistake this guide opened with.

Manufacturer spec: acrylic concrete protective sealer, satin finish, resistant to moisture, salt and tire pickup, for coated and uncoated horizontal surfaces.

Pros

  • Film-forming finish resists salt, oil and tire pickup on walked surfaces
  • Satin sheen holds up well on pavers and walkways
  • Widely stocked, well-established formula

Cons

  • Not for vertical brick walls or chimneys — film-forming sealers need to stay on horizontal, walked surfaces
  • Will need stripping and reapplication if it starts to yellow or wear thin

Best for

  • Brick or concrete pavers, walkways and patios that take foot traffic, oil and salt exposure

Check Price on Amazon ->

Via Amazon.com

Pro Tips From the Wall

The first time I sealed a brick chimney, I reached for a glossy film-forming sealer because the client wanted a “wet look” finish on the whole exterior to match a sealed paver patio. It looked great that fall. Two winters later, the brick faces on the sunniest side of the stack started popping off in thin flakes — spalling, caused by water vapor that used to evaporate out through the brick getting trapped behind that glossy film instead, then freezing and expanding each winter. We had to strip the sealer, replace a dozen damaged bricks, and reseal with a breathable penetrating formula instead. Here is what I learned: a sealer’s finish — matte and penetrating versus glossy and film-forming — is not a style choice on vertical brick. It decides whether the wall can still breathe.

A few habits that keep a brick sealer job from backfiring: always test a small, inconspicuous patch first and let it cure a full day before judging the color or sheen, since some formulas darken brick slightly when wet and lighten again once fully cured. Apply in dry weather with no rain forecast for at least twenty-four hours, and never seal brick that still feels damp from a recent cleaning — trapped surface moisture under a fresh sealer coat is the same mistake as trapping vapor long-term, just on a faster timeline. And resist the urge to apply a second heavy coat “for extra protection” on a penetrating sealer; past the point the brick can absorb, the excess just sits on the surface as a hazy film instead of soaking in.

🧱 Stage: SEAL — this comes after cleaning and repair, and is usually the last step

Sealing brick sits in the SEAL stage of an exterior masonry project: after the wall or chimney has been cleaned and any damaged mortar or spalled brick has been repaired, and before nothing else — a properly applied brick sealer is typically the final step, not a base for something else on top. Sealing over dirt, efflorescence salts or unrepaired cracks just locks those problems in place underneath a fresh coat.

Coverage & Reapplication Estimator

This is general planning guidance based on common brick sealer coverage rates, not a measurement of any specific product’s performance. Brick porosity, surface condition and the exact formula you choose will change the real numbers — always check the manufacturer’s coverage rate on the can first.





Exterior brick wall close up

How to Choose a Brick Sealer That Will Not Trap Moisture

Every brick sealer on the market falls into one of two categories, and picking the wrong one for the surface you are treating is the single biggest reason a sealing job causes damage instead of preventing it. Decide on mechanism first, then on finish and formula base.

Penetrating (Silane/Siloxane) vs. Film-Forming (Acrylic/Wet-Look) Sealers

A penetrating sealer, like the DRYLOK, Rain Guard and MasonryDefender picks above, soaks into the brick and reacts below the surface, leaving the pores open enough for water vapor to escape while still blocking liquid water from getting in. A film-forming sealer, like the Seal-Krete pick, sits on top as a thin plastic-like coating that can trap vapor underneath it. On a vertical wall or chimney, that trapped vapor has nowhere to go and freeze-thaw cycling does the rest — which is why every serious brick sealer buying guide treats “does it breathe” as the first question, not an afterthought. Film-forming sealers earn their place on horizontal, walked surfaces like pavers, where the trade-off for stain and salt resistance makes sense — the same horizontal-surface logic applies when you are deciding between painting and sealing in the first place; see our masonry paint guide if color is actually what you want, not just protection.

Solvent-Based vs. Water-Based Formulas

Solvent-based penetrating sealers generally penetrate slightly deeper and cure in a wider range of temperatures, but carry stronger fumes and higher VOC content, which matters for application in enclosed spaces or under tight local air-quality rules. Water-based formulas, like all four picks above, have largely closed that performance gap in recent reformulations while being easier to clean up and lower-odor to apply. For most homeowner projects, a water-based penetrating sealer is the easier and safer choice.

Matte/Natural Finish vs. Gloss “Wet Look”

A natural or matte finish leaves brick looking essentially untouched — this is what you want on most walls and chimneys, since a “wet look” is a stylistic choice that only belongs on surfaces built to carry a film-forming coating, like pavers and walkways. If a gloss finish shows up on a penetrating sealer’s label, read the fine print carefully; true penetrating formulas are matte by nature, and a glossy penetrating claim is worth double-checking against the manufacturer spec before you buy.

When NOT to Seal Brick: Understanding the Timing

Do not seal brand-new brick immediately after installation. New mortar and brick need time — commonly six months to a year, depending on climate — to fully cure and let the initial efflorescence (the white, powdery mineral deposits that leach out of new masonry) work its way out on its own. Sealing over active efflorescence traps those salts inside, where they can cause more damage than the water the sealer was meant to stop. Do not seal brick that is already spalling, cracked or has failing mortar joints — repair and repoint first with a guide like our limewash and brick-finish guide, since sealing over damage locks the problem in rather than fixing it. And do not use a film-forming, “wet look” sealer on a vertical wall or chimney for the reasons above — that mismatch is the single most common cause of brick sealer failure.

How to Prep Before You Seal Brick

  1. Clean the brick thoroughly and let it dry fully. Dirt, mildew and loose mortar dust under a sealer coat get locked in place permanently; a pressure washer on a low setting or a masonry cleaner works for most brick, followed by at least two full dry days before sealing.
  2. Repair cracked mortar and spalled brick first. A sealer is not a repair product — it protects sound masonry, it does not fix damaged masonry. See our brick fireplace guide for repointing basics before sealing a chimney breast or firebox surround.
  3. Confirm the brick has fully cured if it is new or recently repointed. Give new mortar the manufacturer’s full cure window, usually a matter of months, before sealing.
  4. Match the sealer type to the surface — penetrating for walls and chimneys, film-forming for pavers and walkways — using the picker above as a starting point.
  5. Test on a small, inconspicuous patch first. Let it cure a full day before judging color and sheen, since wet and cured appearance can differ noticeably.
  6. Apply in dry weather with no rain in the forecast for at least 24 hours, and avoid applying in direct, intense sun that can flash-dry the sealer before it penetrates properly.
  7. Protect your eyes and skin while applying, and ventilate if working with a solvent-based formula; the respiratory protection guidance OSHA publishes applies to extended sealer application in enclosed or poorly ventilated areas. If the brick is on a home built before 1978, review the EPA’s lead-safe renovation program before pressure washing or disturbing old mortar or paint, since cleaning can release lead dust from older coatings.
  8. Apply a thin, even coat and avoid puddling. A penetrating sealer that pools on the surface instead of soaking in just sits there as a hazy residue once it dries.

The Verdict

For most standard exterior brick walls, the DRYLOK Siloxane 7 is the one to reach for first — it penetrates rather than films over, leaves no color change, and is rated for brick, concrete and masonry in one can. If you are sealing brick that is new, freshly repointed or just pressure-washed, the Rain Guard Brick Sealer is formulated for exactly that surface rather than concrete first. For a chimney specifically — the most weather-exposed brick on most houses — the MasonryDefender Chimney Brick Sealer is built for that job, though remember it is a height-access task. And if what you are actually sealing is brick pavers or a walkway rather than a wall, skip the penetrating formulas entirely and use the Seal-Krete Clear-Seal, since a film-forming sealer belongs on horizontal, walked surfaces, not vertical brick.

Frequently Asked Questions

Does sealing brick stop efflorescence?

Sealing can reduce new efflorescence by limiting the water that dissolves and carries mineral salts to the surface, but it will not remove efflorescence that is already there, and sealing over active efflorescence on new brick traps those salts inside instead of letting them finish leaching out.

How often should you reseal brick?

Most penetrating brick sealers are rated for roughly five to seven years on a wall exposed to full weather, though more porous or older brick can wear through protection faster, closer to three to five years. Check the manufacturer’s specific rating, since formulas vary.

Can sealing brick too soon after installation cause problems?

Yes. New brick and mortar typically need six months to a year to fully cure and let initial efflorescence work its way out. Sealing before that window closes traps moisture and salts inside the masonry instead of letting them resolve naturally.

Does a brick sealer change the color or look of the brick?

A true penetrating sealer in a natural or matte finish should leave brick looking essentially unchanged once fully cured, though it may look slightly darker or wet-looking while curing. A film-forming “wet look” sealer will add visible sheen, which is a different, more noticeable finish.

Do brick chimneys need to be sealed?

A chimney is one of the most weather-exposed sections of brick on most houses, with no roof overhang to shed rain away from it, which is why a dedicated penetrating sealer is commonly recommended for chimney brick specifically rather than skipped.

What is the difference between a sealer and a waterproofing coating for brick?

A penetrating sealer soaks in and repels water while staying breathable, so vapor already inside the wall can still escape. A heavier waterproofing coating typically forms a thicker film on the surface, which can block vapor from escaping unless the product is specifically rated as vapor-permeable for exterior masonry.

Can a brick sealer trap moisture and cause spalling?

Yes, if you use a film-forming, non-breathable sealer on a vertical wall or chimney. Trapped water vapor behind a non-breathable coating has nowhere to go, and freeze-thaw cycling can pop brick faces off over one or two winters. This is why penetrating, vapor-permeable formulas are the standard pick for vertical brick.

S

Sophie Ulman

Sophie Ulman has renovated and painted more rooms than she can count — and made every mistake in the book so you don’t have to. She focuses on real-world durability: not how products perform on day one, but whether the repair holds through a full seasonal cycle.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *